ICP Alltek

  1. ICP Alltek
  2. Products
  3. Airless fillers
  4. Alltek X

Alltek X

Date de dernière modification

DESCRIPTION
Light roughing and skimming coating for airless and high-pressure screw machine applications indoors or outdoors. Alltek X is a ready-to-use grey paste plaster based on light fillers, particularly water-resistant and with a high filling power.

USE
Indoors:

  • Walls and ceilings on all common substrates with planimetry defects
  • Ideal for aerated concrete blocks and raw concrete thanks to its filling power
  • Easy to straighten
  • Manual application possible
  • Can be used in damp rooms
 On location:

  • Coating of balcony undersides
  • Repair of the pre-slab joints
  • Roughing of the supports
  • Can be coated with all types of exterior paints: waterproofing coatings, thin films, RPE, CSR
  • The plaster must be covered with paint
Typical spreadability 1 to 4.5 L/m² per pass
Recommended thicknesses
  • Min. thickness: 0,6 mm
  • Max. thickness: 3 mm per pass
Packaging
  • 15 L (20.1 kg) plastic bucket.
  • 15 L (20.1 kg) plastic bag with handle.

Détails

TECHNICAL SPECIFICATIONS

Typical Spreadability

1 to 4.5 L/m² per pass.

Density

1,34 +/- 0,10 kg/l

Solid Content

  • Solid content by mass: 69%
  • Solid content by volume: 58%

Application conditions

  • +5°C to +35°C
  • Max. relative humidity 70%

pH

8 +/- 1

Cleaning tools

With water

Drying

  • 48 hours on average depending on application thickness, temperature, ventilation, humidity and type of substrate. Sanding and recoating: after complete drying.
  • The plaster will find its final shade (grey) when it dries completely.

Recommended thicknesses

  • Min. thickness: 0,6 mm
  • Max. thickness: 3 mm

CHARACTERISTICS
  • Ready to use
  • Ease of use
  • Excellent adhesion (>2.5 N/mm² on concrete)
  • Very good slip power and water resistance
  • Fire classification: B-s2, d0
  • Classification: family III class 2 and family IV class 4b according to AFNOR NF T36-005, compliant with AFNOR NF EN 15824, compliant with AFNOR NF EN 16566
  • Identification code according to EN 16566: G0S1V2W3A0C0RA 
  • Liquid water permeability: W3 according to EN 1062-3
  • Water vapour permeability: V2 according to ISO 7783

PACKAGING AND STORAGE
  • 15 L (20.1 kg) plastic bucket.
  • 15 L (20.1 kg) plastic bag with handle.
  • 112 L drum
  • Storage for 9 months in original unopened packaging, protected from frost and high heat.

ENVIRONMENTAL INFORMATION
  • VOC content: < 1 g/l.
  • Indoor Air Emission Class

METHOD OF APPLICATION

Substrates:

  • Raw concrete (slabs, pre-slabs, panels, cinder blocks)
  • Aerated concrete block after the splinters have been repaired.
  • Brick tiles, single-wall bricks, plaster tiles, cardboard plasterboard, plaster.
  • Old painted backgrounds adhering and in good condition, porcelain stoneware and glass paste.
  • Type OC3 coatings. For any other type of lime plaster, carry out an adhesion test of 1 m² beforehand. After 24 hours, perform a tear test.

Preparation of substrate:

  • The substrates, preparatory work and application conditions must be compliant with applicable building trade regulations (e.g. DTU) and standards.

Application tips:

  • Any airless pump, flow > 5L (do not use a filter), T-Max airless pump or airless high-pressure screw machine. Airless nozzles from 35 to 55 depending on the condition of the support and the material used (comply with the manufacturer’s advice).
  • Traditional screw machine. Nozzles from 4 to 6 mm depending on the condition of the substrate and the material used (comply with the manufacturer’s advice).
  • Apply a first smoothed coat in a thick thickness (3mm). After drying, apply a second, less heavy coat to obtain a better finish.
  • Sand manually or mechanically to obtain a smooth surface (grit 100 to 150).

Recommendations:

  • Indoors, ensure adequate ventilation to remove excess moisture and speed up drying.

HEALTH AND SAFETY
The safety information sheet is available from: www.icp-alltek.com/en-gb/documentation/